| C0806-2 |
Packaging of components for automatic handling-Part 2: Tape packaging of components with unidirectional leads on continuous tapes |
|
3 |
|
※Japanese Standards Association |
b |
| C0806-3 |
Packaging of components for automatic handling-Part 3: Packaging of surface mount components on continuous tapes |
|
3 |
|
※Japanese Standards Association |
b |
| C2570-1 |
Directly heated negative temperature coefficient thermistors-Part 1: Generic specification |
|
3 |
|
※Japanese Standards Association |
b |
| C5101-1 |
Fixed capacitors for use in electronic equipment-Part 1: Generic specification |
31.060.10 |
5 |
IEC 60384-1 |
※Japanese Standards Association |
b |
| C5101-2 |
Fixed capacitors for use in electronic equipment-Part 2: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric DC capacitors |
31.060.30 |
5 |
IEC 60384-2 |
※Japanese Standards Association |
b |
| C5101-13 |
Fixed capacitors for use in electronic equipment -Part 13: Sectional specification- Fixed polypropylene film dielectric metal foil d.c. capacitors |
|
3 |
|
※Japanese Standards Association |
b |
| C5101-14 |
Fixed capacitors for use in electronic equipment-Part 14: Sectional specification-Fixed capacitors for electromagnetic interference suppression and connection to the supply mains |
|
3 |
|
※Japanese Standards Association |
b |
| C5101-25 |
Fixed capacitors for use in electronic equipment-Part 25: Sectional specification-Fixed aluminium electrolytic surface mount capacitors with conductive polymer solid electrolyte |
31.060.40;31.060.50 |
5 |
IEC 60384-25 |
※Japanese Standards Association |
b |
| C5160-1 |
Fixed electric double-layer capacitors for use in electric and electronic equipment-Part 1: Generic specification |
|
3 |
|
※Japanese Standards Association |
b |
| C5201-2 |
Fixed resistors for use in electronic equipment-Part 2: Sectional specification: Leaded fixed low-power film resistors |
|
3 |
|
※Japanese Standards Association |
b |
| C5201-4 |
Fixed resistors for use in electronic equipmentPart 4 : Sectional specification : Fixed power resistors |
|
3 |
|
※Japanese Standards Association |
b |
| C5402-8-3 |
Connectors for electrical and electronic equipment-Tests and measurements-Part 8-3: Static load tests (fixed connectors)-Test 8c: Robustness of actuating lever |
31.220.01 |
5 |
IEC 60512-8-3 |
※Japanese Standards Association |
b |
| C5402-15-2 |
Connectors for electronic equipment-Tests and measurements-Part 15-2: Connector tests (mechanical)-Test 15b: Insert retention in housing (axial) |
|
3 |
|
※Japanese Standards Association |
b |
| C5932-3 |
Optical isolators-Part 3: Non-connectorized single-mode fiber optic isolators |
|
2 |
|
※Japanese Standards Association |
b |
| C5952-1 |
Fiber optic active components and devices-Package and interface standards-Part 1: General and guidance |
|
3 |
|
※Japanese Standards Association |
b |
| C5952-2 |
Fibre optic active components and devices-Package and interface standards-Part 2: SFF MT-RJ 10-pin transceivers |
|
2 |
|
※Japanese Standards Association |
b |
| C5952-3 |
Fibre optic active components and devices-Package and interface standards-Part 3: SFF MT-RJ 20-pin transceivers |
|
2 |
|
※Japanese Standards Association |
b |
| C5953-3 |
Fiber optic active components and devices-Performance standards-Part 3: Modulator-integrated laser diode transmitters for 40 Gbit/s fiber optic transmission systems |
|
3 |
|
※Japanese Standards Association |
b |
| C5953-4 |
Fiber optic active components and devices-Performance standards-Part 4: 1 300 nm fiber optic transceivers for gigabit Ethernet application |
|
3 |
|
※Japanese Standards Association |
b |
| C5964-4 |
Fiber optic connector interfaces-Part 4: Type SC connector family (F04 Type) |
33.180.20 |
5 |
IEC 61754-4 |
※Japanese Standards Association |
b |
| C5964-6 |
Fiber optic connector interfaces-Part 6: Type MU connector family (F14 Type) |
33.180.20 |
5 |
IEC 61754-6 |
※Japanese Standards Association |
b |
| C5965-3-31 |
Fiber optic interconnecting devices and passive components-Connector optical interfaces-Part 3-31: Connector parameters of single mode physically contacting fibers-One-row 8 degree angled rectangular polyphenylene sulphide ferrules |
33.180.20 |
5 |
IEC 61755-3-31 |
※Japanese Standards Association |
b |
| C6020 |
General rules and testing methods for intercommunication equipments |
|
1 |
|
Japan Intercom Industry Association |
b |
| C6122-1-0 |
Optical amplifiers-Test methods-Part 1-0: Power and gain parameters |
|
4 |
|
※Japanese Standards Association |
b |
| C6122-1-1 |
Optical amplifiers-Test methods-Part 1-1: Power and gain parameters-Optical spectrum analyzer method |
|
4 |
|
※Japanese Standards Association |
b |
| C6184 |
Test methods of optical power meters for optical fiber |
|
4 |
|
※Japanese Standards Association |
b |
| C6802 |
Safety of laser products |
|
1 |
|
Optoelectronics Industry And Technology Development Association |
b |
| C6822 |
Test methods for structural parameters of optical fibers-Dimensional characteristics |
33.180.10 |
5 |
IEC 60793-1-21,IEC 60793-1-22,IEC 60793-1-20 |
※Japanese Standards Association |
b |
| C6824 |
Test modes for bandwidth of multimode optical fibers |
|
2 |
|
※Japanese Standards Association |
b |
| C6829 |
Calibration of fibre optic chromatic dispersion test sets |
|
4 |
|
※Japanese Standards Association |
b |
| C6834 |
Plastic cladding multimode optical fibers |
|
2 |
|
※Japanese Standards Association |
b |
| C6835 |
Silica glass single-mode optical fibers |
|
2 |
|
※Japanese Standards Association |
b |
| C6842 |
Measurement methods and test procedures-Polarization mode dispersion of optical fibers |
33.180.10 |
5 |
IEC 60793-1-48,IEC 60793-1-1 |
※Japanese Standards Association |
b |
| C6870-3 |
Outdoor optical fiber cables-Part 3: Sectional specification |
33.180.10 |
5 |
IEC 60794-3 |
※Japanese Standards Association |
b |
| C6870-3-10 |
Optical fiber cables-Part 3-10: Outdoor cables-Family specification for duct, directly buried or lashed aerial optical telecommunication cables |
33.180.10 |
5 |
IEC 60794-3-10 |
※Japanese Standards Association |
b |
| C6870-3-20 |
Optical fiber cables-Part 3-20: Outdoor cables-Family specification for self-supporting aerial telecommunication cables |
33.180.10 |
5 |
IEC 60794-3-20 |
※Japanese Standards Association |
b |
| C60068-2-21 |
Environmental testing-Part 2-21: Tests-Test U: Robustness of terminations and integral mounting devices |
19.040;31.190 |
5 |
IEC 60068-2-21 |
※Japanese Standards Association |
b |
| C61300-1 |
Fiber optic interconnecting devices and passive components-Basic test and measurement procedures-Part 1: General and guidance |
|
4 |
|
※Japanese Standards Association |
b |
| C61300-2-1 |
Fiber optic interconnecting devices and passive components-Basic test and measurement procedures-Part 2-1: Tests-Vibration (sinusoidal) |
|
2 |
|
※Japanese Standards Association |
b |
| C61300-2-5 |
Fiber optic interconnecting devices and passive components-Basic test and measurement procedures-Part 2-5: Tests-Torsion |
|
4 |
|
※Japanese Standards Association |
b |
| C61300-2-18 |
Fiber optic interconnecting devices and passive components-Basic test and measurement procedures-Part 2-18: Tests-High temperature |
|
2 |
|
※Japanese Standards Association |
b |
| C61300-2-46 |
Fiber optic interconnecting devices and passive components-Basic test and measurement procedures-Part 2-46: Tests-Damp heat, cyclic |
33.180.20 |
5 |
IEC 61300-2-46,IEC 61300-2-46 Corrigendum 1 |
※Japanese Standards Association |
b |
| C61300-3-4 |
Fiber optic interconnecting devices and passive components-Basic test and measurement procedures-Part 3-4: Attenuation |
|
3 |
|
※Japanese Standards Association |
b |
| C61300-3-7 |
Fiber optic interconnecting devices and passive components-Basic test and measurement procedures-Part 3-7: Examinations and measurements-Wavelength dependence of attenuation and return loss of single mode components |
33.180.20 |
5 |
IEC 61300-3-7 |
※Japanese Standards Association |
b |
| C61300-3-33 |
Fiber optic interconnecting devices and passive components-Basic test and measurement procedures-Part 3-33: Examinations and measurements-Withdrawal force of a split sleeve using pin gauges |
33.180.20 |
5 |
IEC 61300-3-33 |
※Japanese Standards Association |
b |
| C62368-1 |
Audio/video, information and communication technology equipment－Part 1: Safety requirements |
|
1 |
|
Japan Business Machine And Information System Industries Association |
b |
